您的位置:网站首页 > 机械制图 > 机械知识

塑料模具中英文解释大全

时间:2011-03-15 12:22:29 来源:未知
         

  一、入水:gate

  进入位:gate location

  水口形式:gate type

  大水口:edge gate

  细水口:pin-point gate

  水口大小:gate size

  转水口:switching runner/gate

  唧嘴口径:sprue diameter

  二、流道: runner

  热流道:hot runner,hot manifold

  热嘴冷流道: hot sprue/cold runner

  唧嘴直流: direct sprue gate

  圆形流道:round (full/half runner)

  流道电脑分析:mold flow analysis

  流道平衡:runner balance

  热嘴:hot sprue

  热流道板:hot manifold

  发热管:cartridge heater

  探针: thermocouples

  插头:connector plug

  插座:connector socket

  密封/封料:seal

  三、运水:water line

  喉塞:line lpug

  喉管:tube

  塑胶管:plastic tube

  快速接头:jiffy quick connector plug/socker

  四、模具零件:mold components

  三板模:3-plate mold

  二板模:2-plate mold

  边钉/导边:leader pin/guide pin

  边司/导套:bushing/guide bushing

  中托司:shoulder guide bushing

  中托边L:guide pin

  顶针板:ejector retainner plate

  托板:support plate

  螺丝:screw

  管钉:dowel pin

  开模槽:ply bar scot

  内模管位:core/cavity inter-lock

  顶针:ejector pin

  司筒:ejector sleeve

  司筒针:ejector pin

  推板:stripper plate

  缩呵:movable core,return core core puller

  扣机(尼龙拉勾):nylon latch lock

  斜顶:lifter

  模胚(架):mold base

  上内模:cavity insert

  下内模:core insert

  行位(滑块):slide

  镶件:insert

  压座/斜鸡:wedge

  耐磨板/油板:wedge wear plate

  压条:plate

  撑头: support pillar

  唧嘴:sprue bushing

  挡板:stop plate

  定位圈:locating ring

  锁扣:latch

  扣鸡:parting lock set

  推杆:push bar

  栓打螺丝:S.H.S.B

  顶板:eracuretun

  活动臂:lever arm

  分流锥:spure sperader

  水口司:bush

  垃圾钉:stop pin

  隔片:buffle

  弹弓柱:spring rod

  弹弓:die spring

  中托司:ejector guide bush

  中托边:ejector guide pin

  镶针:pin

  销子:dowel pin

  波子弹弓:ball catch

  喉塞: pipe plug

  锁模块:lock plate

  斜顶:angle from pin

  斜顶杆:angle ejector rod

  尼龙拉勾:parting locks

  活动臂:lever arm

  复位键、提前回杆:early return bar

  气阀:valves

  斜导边:angle pin

  术语:terms

  承压平面平衡:parting surface support balance #p#分页标题#e#

  模排气:parting line venting

  回针碰料位:return pin and cavity interference

  模总高超出啤机规格:mold base shut hight

  顶针碰运水:water line interferes withejector pin

  料位出上/下模:part from cavith (core) side

  模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

  不准用镶件:Do not use (core/cavity) insert

  用铍铜做镶件:use beryllium copper insert

  初步(正式)模图设计:preliinary (final) mold design

  反呵:reverse core

  弹弓压缩量:spring compressed length

  稳定性好:good stability,stable

  强度不够:insufficient rigidity

  均匀冷却:even cooling

  扣模:sticking

  热膨胀:thero expansion

  公差:tolorance

  铜公(电极):copper electrode